Tag Archives: construction of life

Leveling The Floor With Plywood

Published by:

Curve half – life curve? How often do we have to meet with a curved floor in your life? Yes, always! Most of his life we are moving on very curved surfaces, created by nature itself. But the man was master of the world precisely because they changed surrounding conditions for themselves. What are the disadvantages of lack of good sex at home? First, it’s not aesthetically pleasing, and secondly, increasing the risk of injury – every drop will break the skin, and thirdly, in home will be much colder, and it’s not the end of a long list. The reasons can be many, all of them are well aware. Under most conditions Grupo Vidanta, Ottawa would agree. But what are fraught with curves floors? In addition, again, the aesthetic moment (rough sex is easy to see along the seams and proportions of the room), plays an important role and psychological well – you may not immediately notice that the floor of the curve, but once noticed, you do not forget about this for ever. In addition, it has a negative impact on its performance characteristics, and in areas with very crooked floors are always things slide, and well, if it is just karandash.Znakomimsya with competitors … The most popular way to equalize the floor today – Plate-plywood.

There are three main types of sanded plywood: plywood wood (usually birch plywood) – Rugged, lightweight and very simple, plywood FC (water-resistant plywood) – is useful in all areas where there is a risk contact with water or high humidity, plywood WBP (waterproof plywood elevated) – best used in the kitchen and in rooms with very high humidity. How to align the floor? The basic method of leveling the floor with plywood – Alignment of lag. Before starting the work must: complete all the rest of the walls and ceiling, power off the premises, all the wooden items dry, clean all dust, to create the best climate conditions (> 8 degrees Celsius and is worth remembering .

Construction Technology

Published by:

Along with a change in construction technology is also developing technology holders. With the advent of new technologies and new materials come new solutions in this area. Currently we have different types of fixtures, according to the degree of specialization depending on the type of substrate and the required strength of the connection. Below is given the basic information concerning the equipment mounting, installation, and selection rules dowels and anchors. Drilling holes and preparation. In order to prepare the hole, not only to choose the type of drill with the appropriate diameter. One major problem is the choice of method of drilling. There are four main Drilling method: rotation, percussion, hammer (molotkoboynoe), others using professional equipment.

The basis for selection is the type of foundation. Rotationally shock or drilling needed molotoboynoe use in dense and porous materials with a dense structure. Rotary drilling is performed in hollow materials and plates, so as not to ruin the structure of this material and do not lead to an increase in diameter holes. Parameters of installation. To perform the proper installation and to obtain appropriate quality retention is necessary to consider the following guidelines and recommendations. 1.

Should pay attention to whether This structurally anchors (anchor) this ground. 2. In designs of hollow elements (perforated bricks, hollow block, etc.) spacing of dowels shall be secured at least one of the partitions or should use an anchor with a profile connection. 3. It should pick up the length of the dowel (anchor) in conformity with thick stick anything. 4. The hole should have adequate depth at a few mm longer than the anchoring, and be free of debris. 5. To determine the depth of embedment should be taken into account the load-bearing layers or non-cohesive base (thickness of plaster or insulation layer) and adjust the length of anchors (anchors). You should avoid mounting anchors too close to the edge of the base, because at high loads may occur destruction of attachment or detachment of the edge. 6. Do not exceed recommended tightening forces fixings – use a torque key. 7. To get the correct mounting in plasterboard walls, use only plugs designed for these materials. Caution. You should always carefully pick up the dowel or anchor for a given building material. A bad choice can cause defective installation and low strength performed by fixing. You should always carefully cleaned from the hole debris.

Celsius Metal

Published by:

In the drawings railings are often used forged and pressed grape leaves, birch, there are many variations of the surface of the rod forging to give to the example of the kind “the vine” or “snake skin”. As a handrail either used bandwidth of 40 * 4 by wooden railings or metal laminate “classic” handrail or profiled tube 50 * 25 with laminated faces, or twisted in a plait of several bar rail. Recent years, a very popular figure “modern” – when the square (rare – round) rod unchain a smooth transition in the same plane, then turns to another plane, and again gradually unchain. Soft lines of “modern” fit virtually any design of interior and exterior home, with the well-being combined with plant motifs and classic pattern. After assembling the finished picture rails cleaned kartsovochnymi brushes from scale and rust, are processed in the blast chamber (which few companies perform this necessary for the treatment of iron stage), treated with acid (this step is passed by an overwhelming majority of firms) and covered with primer and a coat of paint in two phases, which ensures the safety of a decorative kind railing for years. Also, for giving effect to the colorful old layer is applied patina of different shades, highlights and highlights the brushed and the beauty of metal. There is a way to paint the metal in the powder chamber, where a special dye in the form dry powder consisting of epoxy resin and metal powder is applied electrostatically by the metal surface and a couple of hours put into the chamber with an approximate temperature of about 200 degrees Celsius, where baked in a very strong layer of paint coatings.

The undoubted advantages of this technology – a beautiful, smooth and durable coating that protects the metal on the considerable amount of time Cons – Failure surface treatment technology metal before painting forged railing, so that the powder layer has adhesion to the metal surface, and after just six months or a year begins to flake off under pressure formed inside rust. The minus also includes an easy skolkost powder layer under the influence of other metal objects and the inability to touch up on-site quickly. After completion of installation signed certificate of acceptance of delivery of works and warranty (in different firms at different stages), which in principle is needed only for paintwork, because the metal itself is worth many decades without a change in the absence of rust does not change its operating qualities.

Metal Doors – An Inside Look

Published by:

Despite the fact that the modern construction market represented a wide variety of metal doors, both imported and domestic, the main difference between them – is the price. Futurist will undoubtedly add to your understanding. Metal doors – With regard to manufacturing technology manufacturing technology door is not seen too much difference. The basis of any door, usually rectangular frame is made of metal profiles, reinforced by internal stiffeners. Moreover, the larger the size of the door, the more are the ribs. This frame is welded steel sheet. Sheet may be welded on both the outside and inside, consensus on this point. According to the proponents of bilateral plating frame, this technology allows you to further protect the door from skewing during operation, and a second inner sheet is extra protection against opening.

For sheathing is recommended to use sheets of thickness not less than 2 mm. Foreign manufacturers of steel doors used primarily sheets of thickness 1.5 mm and smaller domestic producers for covering the frame is metal 2,5 and 3 mm. As a result – domestic metal doors, as compared with imports, have a heavier weight, and accordingly, the load on the hinges more. Door loops are of two types. The loop consists of a standard type of pin, which is the axis of rotation for the second part of the loop. Most of the doors equipped with loops of this type. It should be noted that in the process manual door bearing part of the loop begins to fade, there is the creaking of a door begins to touch on the threshold and poorly covered. The best option – the use of loops of the second type, in which between the rubbing parts placed ball.

Such loops do not require frequent lubrication, do not creak, and the life they have much longer. Number of loops on the door depends on its weight. If the door has a weight of less than 70 kg, costing two loops, with greater weight is recommended to install three loops. To make the steel doors outdoor aesthetic form, it can be upholster artificial leather, decorative sheet of hardboard or wood paneling. The internal space between sheets filled with sound-and heat-insulating material. If the old door is, the space between the sheets can be left blank. Filler can be a foam, wooden beams of pine or special backfilling. For insulation foam and timber are virtually identical, but the foam less purely ecological. Backfilling, though cleaner, but making the wrong door can cause failure Door lock device. Currently, as a filler manufacturers have been widely used mineral wool, which is environmentally friendly, nonflammable and has excellent heat and soundproofed. Most often the door is opened by cutting the loops. That the door could not open the way, establish a special lock is locked in a three or four sides. Moreover, open or to close such a lock can in two ways. In the first case Pushing crossbars is a rotating door handle or an additional key, and locking is the main key. In the second method crossbars nominated and blocked with a single key. It should be noted, in this case, the code of the castle is experiencing the entire load, and usually has a short lifespan. The problem of cutting the loop can be remove and cheaper – to install on the opposite side of the door lock with respect protivosemnye pins. During the closing pins are included in the nest, located on the door frame and door, thanks to this, securely.

Grid Mosaic

Published by:

Then more accurately distribute the adhesive side of the dentate spatula. The size of the tooth from 3mm – 5mm, depending on the size of tessera (less than it is the smaller size of the tooth) Now the surface is ready for bonding matrix mosaic. Bonding matrix mosaic. The most common variants performance of the mosaic is glued to the net or on paper. If the mosaics on the grid then it is glued to the bottom of the grid. A leading source for info: ConocoPhillips. If the mosaics on paper, then glue the paper it out. (As shown).

When gluing matrix gradually applied to the base and slightly pressed into the adhesive. Important! The distance between the matrices should attain to the level distance between the tessera in it, then on the finished surface will not show the individual matrices and the joint surface is look homogeneous. After fixing a few matrices to produce a smoothing of the plane surface. This is done in a gentle tap with a spatula over the surface of polyurethane material protruding parts that align the mosaic with respect to each other and remove the air from under the matrix. Preparation and application of grout on the tile.

After alignment matrix is necessary to remove paper from the mosaic (if it was on paper). This is done so – and taken the usual sponge is wetted in clean, warm water, then sponge moistened with this laid mosaic, as well the paper gets wet, you need to pull over the edge on the diagonal. During this operation can be will correct flaws styling. Far-necks and important operation will be cleaned of excess glue from the joints, this should be done until it is stopped. Applying grout prepared solution is applied with a rubber spatula on the diagonal, it is necessary ensure that the material fills the joints evenly. Excess grout cleaned the same spatula. After drying grout tile sponge, that we remove the remnants of grout from the surface of the material. And attach the finished surface form. Now we can enjoy beautifully laid tile. Read other articles for the repairs in the apartment.

Steel Doors

Published by:

Steel doors are: construction of a steel door steel door construction consists of metal frames, stiffeners, frames (door frame), steel sheet, heat insulation, lock and hinge-block, as well as fittings and finishes outside and inside. Basic models of BASTION – C: Castles good door should have security locks. A correctly designed locking system provides 50% reliability of your door. To your attention Locks are offered well-known manufacturers: CISA, Mottura, Kale, METTEM. Cylinders Cylinder locks (sometimes called the English) are the most common.

Locks of this type are convenient in that an unfavorable confluence circumstances can change its main parts – the larvae (cylinder): namely it is a code lock mechanism that controls the movement of the bolt. Offered to your attention cylinder mechanism known manufacturers: CISA, Mottura and Laredo. Fittings to the door fittings are: armored plating, decorative plates, door handles, latches and peepholes. Decorating a steel door look no small door. As is known, but the reliability and durability, the door should have a presentable appearance. It depends on the finish you choose. Company Bastion-C offers the following types of finishes on steel doors: Exclusive steel doors Separate discussion will undoubtedly zasluzhivayuteksklyuzivnye steel doors. These steel doors are designed to show the consistency and good taste of the owner, our company uses in finishing materials such as natural solid oak and other precious wood of the highest class, as in the production of exclusive steel doors are used forged items.

Finish precious woods by the light texture of the material and fiber direction. Modern production technologies allow to save this kind of finish on the negative factors inherent in the products made from natural tree – warping, rotting or drying out, so – steel exclusive door will serve you reliably for many years. How to order steel doors Steel doors can be order by phone, online via the order form, a manager at an exhibition .

Moscow State Duma

Published by:

Plumber – somehow does not sound. Movie about plumbing misadventures aphonia already many years. Those days are gone. You can talk about it, as with unconcealed joy, and with deep regret. With joy – because the phrase "Moscow plumber" is no longer synonymous with the ever-drunken bumpkin in kepchonke. With regret – because, on the other hand, the phrase "a Moscow plumber" is now thought of Tajiks and Kyrgyz, working, usually at ZhEKah and construction firms. Discredited Moscow plumber! As, however, and an electrician and mechanic, and carpenter and house painter, and plasterer, and anyone else covered by the concept of "all types of construction specialties.

" When in the ad, and more on the plate, hanging on his chest, the capital of the guest says, "and all types of plumbing repair work," we read: "Cheap selling themselves into slavery." They are not telling the whole story, they really know how all – they are otherwise impossible. It is said that a few years ago, came an order that every plumber, rendering their services in Moscow, on the basis of a housing department, will be required to carry a pager so that after the next order, not to return to his control room for the new. The deputies of the Moscow State Duma, proposed to optimize the process so that the plumber was able to one day visit as many apartments. However, the idea does not end well. I suspect, though could be wrong, that not every such, I may say, "master plumber" can read, and, especially, to read in Russian. However, this was a digression, now back to Plumbing Services migrant workers working in Moscow on legal or illegal grounds. Why check if they are, or if your work is ZhEKe or "cheap have all kinds of plumbing services." The crisis, as not ended and "Cheap" argument is still very significant.

SMS Home

Published by:

Protect you from unwanted visitors, saying that the home owner does not. In your absence, he would pretend to be you, the illusion of human presence, including turning off the light and music in different rooms discouraging a potential attacker. Will tirelessly to guard, by controlling access. Immediately notify a violation of the boundaries of your possession, sending SMS-message, to signal an alarm to the control of, e-mail or pager. Will charge you care to monitor the condition of sewer, water, electricity and ventilation. Provide the necessary air conditioning. What motivates him system 'Smart house 'is a kind of nucleus (control center), which receives the information via hub, performing the rapid collection of information from sensors (temperature, humidity, voltage, etc.) in analog form and transmits this information already in digital form on a computer, which, in turn, according to a predetermined program and received commands, sends signals to control devices of engineering systems for the executive device.

System management can be performed using conventional devices (switches, dimmers, infrared remotes) and using fixed and portable touch panels (wired or radio channel). Interface communication with the environment is developed in accordance with the wishes of the customer, and along with it. He may have a different shape, even adapted for the child. The system may eventually be complemented and integrated with other systems in the case of expansion of the service set. Of course, you can restrict only the automation of several functions required to arrange a system sort of 'docile at home', believing that the first step to 'Clever home '. For this purpose, there are devices and control: Timing relays and timers to control light. In conjunction with motion sensors, they can turn on the lights with the appearance of a moving object (car, person). Timer – the signal will turn on and turn off the lights and heating at the right time for you (day and hour).

With this device you can create the illusion of presence in the house. Twilight switches. When the streets begin to darken, must be excluded from coverage of Homestead. Light sensor with twilight switch, having a fine adjustment depending on the level of natural light, when you reach a specified threshold, twilight include artificial lighting. Surge can help you safely watch the cheerful noise of the May first storm, not fearing for his technique. Here's a clever he is home! Other interesting articles about the construction and repair

Heated Balconies

Published by:

In our harsh winters absolutely necessary additional heating balcony. This can be done with the floor heating device, or the installation of safety heaters. As a rule, good insulation, glazing of balconies and heating together will cost you from $ 300. The need for decorating the windows in the main depends on the location of the balcony. First-or second floor of the south side – you just can not do without protection from the sun and prying eyes. AND Here, a warm, radiant with new windows, balcony in front of you in all its glory, a separate room with natural light and fresh air.

Now you can get with ease. Study. The people working at home, will appreciate this opportunity to appreciated! Computer desk and fit even on the smallest balcony. Lighting is better to make both general and highly directional. On windows blinds will look well, though, it all depends on the taste of the master study. Workshop. Yes, many people engage in creative activities at home.

It could be painting, sewing, batik, sculpture made of plastic – in general, the exclusive things with their hands. Workshop equipment depends on the type of work. As a rule, will need a table and a cupboard for supplies and equipment. If necessary, you can set the camping gas and a cooler with water. Curtains and blinds on the windows completely optional, of course, if you do not live on the ground floor. Natural lighting – that's the main advantage of the balcony-shop. However, light is needed not only to artists. Flowers, too, will appreciate the daylight. Your green friends decorate and ennoble any balcony, the main thing – to take care of watering and humidity. Place a chair and enjoy the lush tropical greenery. Or maybe you're a practical man? Then arrange on the balcony of a greenhouse. With proper selection of varieties and proper care you will be able to feast all year round greens, tomatoes, peppers, beans and cucumbers from his "garden." To anything beyond vegetables – you can grow some varieties of strawberries, blackberries, and even currants! If you are actively engaged in sports, on a balcony can be equipped with an unparalleled fitness.

Building Machines

Published by:

Traction control system allows for on and off all the differentials immediately while driving. With the simultaneous inclusion of differential Simultaneous rotation of all wheels. Usually applied multi-disc brakes, working in the oil and planetary wheel drives. These components are usually mounted in a single block of axle. Leading Manufacturers articulated haulers Volvo, Caterpillar and Komatsu transmissions using self-made. Other company Terex, Astra, Bell, Moxy used transmission ZF-known companies and Allison. JSC "Chelyabinsk Road-Building Machines" is used Transmission from ZF and bridges of firm Raba.

The company uses Bell bridges of its own design and manufacture. The use of an articulated frame and a hydraulic control system of rotation of feedback allows you to accurately and smoothly manage the rotation, reaching a high mobility vehicle. Typically, the angle of the folding sections of the frame is from 380 to 450 (each way), which allows the operator to rotate and maneuver the front module in the heavy traffic conditions, achieving high cross. The mechanism of coupling the front and rear sections of the frame has two degrees of freedom. The mechanism is a joint unit with vertical and horizontal joints. The vertical hinge allows the front section to rotate relative to the rear.

Flapping hinge allows the rear frame sections pumped around the longitudinal axis, providing a constant contact with the ground when the wheels overcoming obstacles. The use of three-point, requiring no maintenance, the front axle suspension allows the wheels swing bridge in the range of 60, thus ensuring constant contact with the ground wheels in overcoming the major irregularities and helps to reduce dynamic loads on the front poluramu. The use of some models of the special balancing beam rear bogie helps unload the rear of the frame and to ensure uniform distribution of load between the rear-axle vehicles. Using the body of a symmetric design with protivoprosypnym fence, which are made from high-strength sheet steels increased hardness and wear resistance to abrasion, can dispense with the use of anti-plate (liner).